配置VSFTP服务器,主要参考网上的资料,结合自己实际写下一些体会。
直接用yast命令安装,安装好的文件结构如下:
/etc/init.d/vsftpd 启动脚本
/etc/xinetd.d/vsftpd
/etc/pam.d/vsftpd pam认证文件
/usr/share/doc/packages/vsftpd
/usr/sbin/vsftpd VSFTP主程序
/var/ftp 匿名用户主目录
/var/ftp/pub 匿名用户的下载目录
/etc/vsftpd.conf 配置文件
# Example config file /etc/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all compiled in defaults.
#
# If you do not change anything here you will have a minimum setup for an
# anonymus FTP server.
#
# READ THIS: This example file is NOT an exhaustive list of vsftpd options.
# Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's
# capabilities.
# General Settings
#
# Uncomment this to enable any form of FTP write command.
#
write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
#
dirmessage_enable=YES
#
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#
nopriv_user=ftpsecure
#
# You may fully customise the login banner string:
#
#ftpd_banner="Welcome to FOOBAR FTP service."
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
#
#ls_recurse_enable=YES
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#
#deny_email_enable=YES
#
# (default follows)
#
#banned_email_file=/etc/vsftpd.banned_emails
#
# If enabled, all user and group information in
# directory listings will be displayed as "ftp".
#
#hide_ids=YES
# Local FTP user Settings
#
# Uncomment this to allow local users to log in.
#
local_enable=YES
#
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
#
local_umask=077
#
# Uncomment to put local users in a chroot() jail in their home directory
# after login.
#
chroot_local_user=YES
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
#
chroot_list_enable=YES
#
# (default follows)
#
chroot_list_file=/etc/vsftpd.chroot_list
#
# The maximum data transfer rate permitted, in bytes per second, for
# local authenticated users. The default is 0 (unlimited).
#
#local_max_rate=7200
# Anonymus FTP user Settings
#
# Allow anonymous FTP?
#
anonymous_enable=YES
#
# Anonymous users will only be allowed to download files which are
# world readable.
#
anon_world_readable_only=YES
#
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
#
anon_upload_enable=YES
#
# Default umask for anonymus users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
#
anon_umask=022
anon_root=/sda/educloud
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#
anon_mkdir_write_enable=YES
#
# Uncomment this to enable anonymus FTP users to perform other write operations
# like deletion and renaming.
#
#anon_other_write_enable=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#
chown_uploads=YES
#chown_username=whoever
#
# The maximum data transfer rate permitted, in bytes per second, for anonymous
# authenticated users. The default is 0 (unlimited).
#
#anon_max_rate=7200
# Log Settings
#
# Log to the syslog daemon instead of using an logfile.
#
syslog_enable=YES
#
# Uncomment this to log all FTP requests and responses.
#
#log_ftp_protocol=YES
#
# Activate logging of uploads/downloads.
#
xferlog_enable=YES
#
# You may override where the log file goes if you like. The default is shown
# below.
#
vsftpd_log_file=/var/log/vsftpd.log
#
# If you want, you can have your log file in standard ftpd xferlog format.
# Note: This disables the normal logging unless you enable dual_log_enable below.
#
xferlog_std_format=YES
#
# You may override where the log file goes if you like. The default is shown
# below.
#
xferlog_file=/var/log/xferlog
#
# Enable this to have booth logfiles. Standard xferlog and vsftpd's own style log.
#
#dual_log_enable=YES
#
# Uncomment this to enable session status information in the system process listing.
#
#setproctitle_enable=YES
# Transfer Settings
#
# Make sure PORT transfer connections originate from port 20 (ftp-data).
#
connect_from_port_20=YES
#
# You may change the default value for timing out an idle session.
#
#idle_session_timeout=600
#
# You may change the default value for timing out a data connection.
#
#data_connection_timeout=120
#
# Enable this and the server will recognise asynchronous ABOR requests. Not
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
#
#async_abor_enable=YES
#
# By default the server will pretend to allow ASCII mode but in fact ignore
# the request. Turn on the below options to have the server actually do ASCII
# mangling on files when in ASCII mode.
# Beware that turning on ascii_download_enable enables malicious remote parties
# to consume your I/O resources, by issuing the command "SIZE /big/file" in
# ASCII mode.
# These ASCII options are split into upload and download because you may wish
# to enable ASCII uploads (to prevent uploaded scripts etc. from breaking),
# without the DoS risk of SIZE and ASCII downloads. ASCII mangling should be
# on the client anyway..
#
#ascii_upload_enable=YES
#ascii_download_enable=YES
#
# Set to NO if you want to disallow the PASV method of obtaining a data
# connection.
#
#pasv_enable=NO
# PAM setting. Do NOT change this unless you know what you do!
#
pam_service_name=vsftpd
# Set listen=YES if you want vsftpd to run standalone
#
listen=YES
# Set to ssl_enable=YES if you want to enable SSL
ssl_enable=NO
# Limit passive ports to this range to assis firewalling
pasv_min_port=30000
pasv_max_port=30100
guest_username=virtual_user
user_config_dir=/etc/vsftpd/vsftpd_user_config
user_sub_token=$USER
这种配置允许匿名用户上传东西,但是不允许下载。
分享到:
相关推荐
较为详细地介绍了openSUSE服务器架设方面的内容,是一本不错的参考书
NULL 博文链接:https://wujingenli.iteye.com/blog/2227116
虚拟机VMwareWorkstation7.1.1中安装openSUSE11.3Linux服务器.docx
openSUSE Leap 适用于家庭或者小型办公应用中的很多计算机 设备,比如笔记本、台式电脑、上网本、服务器以及多媒体中心。 openSUSE Leap 是最主要的GNU/Linux发行版之一,并且也是历史最为悠久的发行版之 一。 ...
OpenSUSE10.2.0下面安装ORACLE
学习Open Suse Linux时,经常会遇到Open Suse Linux问题,这里将介绍Open Suse Linux问题的解决方法。现在很多的IT企业部门都想应用Open Suse Linux。本文介绍Open Suse Linux服务器配置方法。
opensuse11.2系统安装资源,可以直接下载,解压安装opensuse11.2系统
opensuse官方入门手册2 opensuse官方入门手册2 opensuse官方入门手册2
opensuse官方入门手册3 opensuse官方入门手册3 opensuse官方入门手册3 opensuse官方入门手册3
opensuse 官方 入门 手册1 opensuse 官方 入门 手册1 opensuse 官方 入门 手册1
OpenSuse Linux 系统安装包
openSUSE设置服务通过防火墙.docx
opensuse环境搭建 opensuse samba
该文档为openSUSE42.3社区版官方文档,经过处理后的,通俗易懂
openSUSE Leap 是 openSUSE 常规发行版本的新名称,在 13.2 之前它仅仅被称为“openSUSE”。 一、openSUSE 发行周期:(15年以前仅有一个openSUSE发行版) 1、openSUSE Leap 是 openSUSE 的常规版本, 在 42.3 ...
OpenSUSE简介.pdf 学习资料 复习资料 教学资源
The Tumbleweed distribution is a pure rolling release version of openSUSE containing the latest stable versions of all software instead of relying on rigid periodic release cycles. The project does ...